The Manufacture of Sterile Pharmaceuticals and Liquid Medical Devices Using Blow-Fill-Seal Technology

Former editions:

1st edition September 1993 by S. Probert, S. Forrester-Coles

1st main revision September 1998 (general update)

2nd main revision October 2002 (general update) by A. Löfgren

small revision January 2003(small revision/update of integrity testing sections) by A. Löfgren

3rd main revision April 2007 (update in general and regarding the revised FDA guidance)

by E. Dewhurst

4th main revision Nov. 2011/March 2012 (general update, Media Fills, SIP, implementation of

rotary machine type 4010) by K. Downey, M. Haerer, S. Marguiller, P. Åkerman

5th corrected version December 2016

The pictures on the front cover are sponsored by Brevetti Angela, Rommelag and Weiler ­Engineering.

Bibliographic data available from the German National Library

The German Library catalogs this publication in the German National Bibliography; detailed bibliographic information can be found on the internet website: http://dnb.ddb.de.

The Manufacture of Sterile Pharmaceuticals and Liquid Medical Devices Using Blow-Fill-Seal Technology: Points to Consider

ISBN 978-3-87193-443-8

© 2017 ECV · Editio Cantor Verlag für Medizin und Naturwissenschaften GmbH, Aulendorf (Germany).

All rights, in particular those of duplication, distribution, and translation are reserved by BFS International Operators Association c/o Melitek A/S, DK-4840 Nørre Alslev, and the publisher without any limit in time. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise without the prior written permission of the publisher. The absence of the symbol ® after any name does not imply that this name is not under trademark protection.

ECV · Editio Cantor Verlag on the internet www.ecv.de

Typesetting: Reemers Publishing Services GmbH, Krefeld

Printing: HOLZMANN DRUCK GMBH & CO. KG, Bad Wörishofen

Contents

Disclaimer 7

1. INTRODUCTION 9

2. OBJECTIVE 11

3. BFS PROCESS OUTLINE 12

3.1 Shuttle Type Machines 12

3.2 Rotary Filling Machines 14

3.3 Additional Applications 16

4. ADVANTAGES & CHALLENGES OF BLOW-FILL-SEAL TECHNOLOGY 18

4.1 Advantages 18

4.2 Challenges 19

5. DESIGN 21

5.1 Product Design 21

5.1.1 Aseptic processing versus terminal sterilisation 21

5.1.2 Terminal sterilisation 21

5.1.3 Polymer 22

5.1.4 Container design 23

5.1.5 Secondary packaging 24

5.2 Equipment Design 25

5.2.1 General 25

5.2.2 Control of critical zone environment 26

5.2.3 Air shower design (shuttle type machines) 27

5.2.4 Product pathway 28

5.2.5 Mould design 28

5.2.6 Deflashing 29

5.2.7 Equipment Monitoring 29

5.2.8 Container closure system leak detection 30

5.3 Facility Design 31

5.3.1 Aseptic Processing Area (APA) 31

5.3.2 Support areas 34

5.3.3 Polymer storage and distribution 34

5.3.4 Utilities 35

6. QUALIFICATION AND VALIDATION 36

6.1 PRODUCT VALIDATION 36

6.1.1 Container/Closure integrity testing 36

6.1.2 Process capability 36

6.2 Equipment Validation 37

6.2.1 Extruder 37

6.2.2 Air Flow 38

6.2.3 Clean in Place (CIP) of the product pathway 38

6.2.4 Sterilisation in Place (SIP) of the product pathway 38

6.2.5 Process simulation (media fill) for aseptic filling lines 40

6.2.6 Moulding and filling system 44

6.2.7 Downstream process 44

6.2.8 Controls 44

6.2.9 Filtration 45

6.3 Facility Validation 45

7. OPERATION 46

7.1 Process Operation 46

7.1.1 In-process controls 46

7.1.2 Start-up procedures 47

7.1.3 Interventions 47

7.1.4 Environmental monitoring 48

7.2 Equipment Operation 51

7.2.1 Sanitisation of “critical” surfaces 51

7.2.2 Equipment cleaning 51

7.2.3 Cooling systems 51

7.2.4 Extruder control 51

7.2.5 Maintenance 52

7.3 Facility Operation 52

7.3.1 Gowning 52

7.3.2 Polymer handling 53

7.3.3 Use of regrind polymer material 53

7.3.4 Training 53

8. RISK ASSESSMENT 55

8.1 Product contamination 55

8.2 Other product quality attributes 57

APPENDIX 59

GLOSSARY 60

GUIDANCE REFERENCES 62

GENERAL REFERENCES 63

Disclaimer

This document was produced and is disseminated by the Pharmaceutical Blow-Fill-Seal International Operators Association (the “Association”) as a service of the Association solely for the convenience of its members. These ‘Points to Consider’ are an effort to provide a compilation of current Blow-Fill-Seal (“BFS”) manufacturing operations and practices. In producing this document, the Association has attempted to reflect accurately the current state of BFS manufacturing operations on a worldwide basis. However, the Association makes no claim whatsoever regarding these ‘Points to Consider’ to any user of these ‘Points to Consider’, including without limitation, any claim that the document:

– contains no errors

– covers all actual or potential aspects of BFS operations

– is in all instances completely up to date in its description or outline of current practice

– represent the unanimous [or consensus] opinion of the BFS industry or the Association members

– reflects the requirements of all applicable laws

All use of these ‘Points to Consider’ shall be at the user’s sole risk.

This document, and the procedures contained in the ‘Points to Consider’, has not been reviewed by, nor have they been endorsed by, filed or registered with, any governmental agency having jurisdiction over these matters. This document do not create any rights for, or confer any rights upon, any person, nor do they operate to bind the international and national authorities (FDA, European Commission, any other federal, state or local regulatory agency), or the public, in any manner. Where these ‘Points to Consider’ reiterate a requirement imposed by statute or regulation, the requirement’s having the force and effect of law is not changed or affected in any way by virtue of its inclusion in this document, nor does such inclusion give these ‘Points to Consider’ the force of law.

The mention in this document of commercial products, their sources, or their use in connection with matters described in the ‘Points to Consider’ is not, and is not to be construed as, either an actual or implied endorsement of such products by the Association.

The Association shall not be liable for, and disclaims all liability for, any and all losses, costs or damages, however arising, whether direct or indirect, incidental, consequential, punitive or exemplary, incurred as a result of or in connection with any person’s following, or failing to follow, these ‘Points to Consider’.

The BFS process is a technical one and appropriate and adequately trained expert personnel must be employed at each stage of the BFS process.

1. INTRODUCTION

Blow-Fill-Seal (BFS) technology has been used for pharmaceutical and liquid medical device manufacturing since the 1970s. This processing technology has become accepted worldwide for both aseptic and terminally sterilised liquid products and is currently used in more than 50 countries throughout the world.

BFS technology lacks harmonisation and specific standards on a worldwide basis. As a result, the technology has developed in an isolated fashion, with each company and each regulatory agency establishing its own interpretation of acceptable BFS practice.

In 1989, the Pharmaceutical Blow-Fill-Seal International Operators Association (BFS IOA) was established as an interest group of pharmaceutical and associated companies actively involved with BFS processing. The Association was formed to provide its members with an opportunity to exchange ideas and opinions, and to formulate agreement on operating standards. It also provides a forum to speak with a unified voice to machine manufacturers, commercial suppliers, and regulatory bodies. The Association has expanded worldwide and now has over 60 member companies.

In an attempt to establish a common understanding of acceptable practice in BFS processing, the Association first published a “Points to Consider for Pharmaceutical Blow-Fill-Seal Manufacturing Operations” (PTC) document in September 1993. The document addressed points specific to BFS processing but also covered many more general areas. The current PTC document focuses on issues specific or unique to BFS technology and has undergone periodic review and systematic updates since its inception.

This document is the culmination of several reviews during 2010 and 2011 and the most current version is from March 2012.

The document is structured into 3 main sections covering design, start-up/validation, and routine operation. Within each section, Product, Equipment and Facility are considered.

	Design	Initial ­start-up	Routine ­operation
Product
Equipment
Facility

2. OBJECTIVE

The objective of the ‘Points to Consider’ document is to provide recommendations specific to the operation of Blow-Fill-Seal technology for the manufacture of sterile pharmaceuticals and liquid medical devices. The principles of BFS technology as applied to filling are considered to be the same in terms of machine process for both aseptically filled and terminally sterilised products.

This document provides information to supplement and to assist with interpretation of international standards and regulatory guidance from the perspective of BFS operations, and considers specific aspects of BFS operation which are not covered by existing published information.

The PTC is intended as a guide for industry and is not meant to supplant or duplicate any existing regulatory guidance. A list of current regulatory guidance references is provided in the Appendix.

3. BFS PROCESS OUTLINE

Blow-Fill-Seal technology is a pharmaceutical filling process in which containers are formed from a thermoplastic granulate, filled with product and then sealed in a continuous, integrated, automatic operation. Originally developed for use in other industries, BFS technology has been adapted for use in the manufacture of sterile pharmaceutical, medical device, biological, and veterinary products. The two most common types of BFS machines are the shuttling machine (with parison cut) and the rotary machine (closed parison) types. Both are considered in this document.

In the process, bulk solution/suspension is delivered to the filling machine, through the filling system to the filling needles (“mandrels”).

Polymer granules are extruded under pressure (up to 350 bar) as a hot (approx. 180°C) mouldable plastic tube (“parison”) or set of parisons.

3.1 Shuttle Type Machines

A downward flow of sterile filtered air is passed through the parison (parison support air) to prevent collapse of the molten tube. The 2 halves of a mould close around the parison(s) to form the body of the container(s). Simultaneously, the newly formed container in the mould is cut free from the parison by a “knife”.

The mould is transferred to the filling position.

The filling mandrel is lowered into the plastic tube and the container is shaped either by vacuum or with sterile blowing air or other inert gas supplied by the mandrel. Subsequently, the container is filled with the required volume of the product. During the liquid fill, headspace gas is displaced from within the container, either through the mandrel or direct to room atmosphere, depending on the container configuration.

The filling mandrel is then raised and the containers are sealed automatically by forming the still hot plastic above the main mould, by closing the upper section of the mould, (head/seal mould). The entire mould assembly then opens, releasing the filled container(s) that have been formed, filled and sealed.

This complete cycle generally takes between 10–20 seconds depending on container design and volume of fill. Parison extrusion continues, as the mould returns to the first station, and the cycle repeats (Fig. 1).

Fig. 1 Schematic representation of the open parison Blow-Fill-Seal process.

3.2 Rotary Filling Machines

There are a number of significant differences between shuttling zone machines and rotary filling machines: